Astatic microphone 878hl. Astatic 877L Microphone 2019-01-25

Astatic microphone 878hl Rating: 7,6/10 1636 reviews

Astatic

astatic microphone 878hl

. The un-insulated wire is most likely the shield around the audio lead mic-gnd. For all industrial and commercial public address and paging applications. Summary of the content on the page No. It's cable looks factory has four conductors red, black, green, white plus an uninsulated shield wire. The rugged, molded Cycolac housing and die-cast zinc base maintain durability while remaining lightweight.

Next

Astatic 878HL user manual

astatic microphone 878hl

The lift-to-talk operation can be disabled with a slide switch located under the microphone base. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. Prices subject to change without notice. Christopher Lee: Thanks for the reply! The wide band frequency response is smooth and peak free. The dynamic capsule requires no power source, and its omnidirectional polar pattern provides a generous pickup area. Four molded, non-skid, non-marring, permanently resilient shock isolation feet are located under the base. My personal favorites are the and.

Next

Astatic microphone lankasri.lk

astatic microphone 878hl

If you want to quickly view the content of pages found on the following pages of the manual, you can use them. In most cases, the mic-gnd and ground are common in the mic. You could also open the mic up and possibly determine the wiring code by peeking inside. The microphone's lift-to-talk operation can be disabled with a slide switch located under the microphone base. Works with high or low impedance systems. The microphone's lift-to-talk operation can be disabled with a slide switch located under the microphone base. The 878 has easily accessible control for volume adjustment so that the correct modulation level can be set for each operators voice.

Next

Astatic 878 Base Mic wire diagram

astatic microphone 878hl

Advertisement Print version Many people prefer to read the documents not on the screen, but in the printed version. The microp Summary of the content on the page No. Can anyone provide a description of the plug pinout for this item? The high or low impedance selector switch is located on the bottom of the microphone. Works by either push to talk or lift to talk. To start viewing messages, select the forum that you want to visit from the selection below.

Next

ASTATIC 878

astatic microphone 878hl

Prices, specifications, and images are subject to change without notice. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. Also has a lock-on switch for long announcements. Its desktop design incorporates four non-skid feet to inhibit slippage and surface marring. Intelligible Sound The 80 Hz to 12 kHz frequency response is smooth and peak free, with a slight rise above 2 kHz to impart enhanced intelligibility.

Next

Astatic microphone lankasri.lk

astatic microphone 878hl

The 878 preamplifier is powered by a readily available, easily replaced, 9 volt battery. The low impedance position is recommended for long cable length requirements. Not responsible for typographical or illustrative errors. For all industrial and commercial public address and paging applications. The 878 has a six wire coil cord which allows for relay, electronic or virtually any type hookup with almost any transceiver. You may have to before you can post: click the register link above to proceed. Priced way below the competition.

Next

Astatic 878 Base Mic wire diagram

astatic microphone 878hl

It is always possible that someone replaced the cord, or may have re-wired it. Non-Skid Feet Four molded non-skid, non-marring feet are located under the zinc die-cast base. Publisher does not accept liability for incorrect spelling, printing errors including prices , incorrect manufacturer's specifications or changes, or grammatical inaccuracies in any product included in the Musician's Friend catalog or website. I will take your advice and investigate the mic wiring myself. Four molded, non-skid, non-marring, permanently resilient shock isolation feet are located under the base.

Next

878HL

astatic microphone 878hl

Any issues with signup please use Contact Us button at bottom of any page. It will be used on an 8 pin Kenwwod rig B-2000. The wide band frequency response is smooth and peak free. Musician's Friend is a registered trademark of Musician's Friend Inc. The Astatic Desktop Mic is manufactured to take abuse and retain its performance and appearance over a long life. With a frequency response of 80 Hz to 12 kHz, its audio output is optimized for vocal transmission. This could easily be checked with an ohm-meter or continuity tester.

Next

Astatic by CAD Omnidirectional Dynamic Desktop Microphone with Locking Switch

astatic microphone 878hl

The high or low impedance selector switch is located on the bottom of the microphone. The low impedance position is recommended for long cable length requirements. Maybe at least narrow down the possibilities. Please specify your exact Radio and Model in the end of your Order Form when Checking out. Modern styling plus rugged construction and environmental resistance will provide dependability in such applications as airport control towers, police, fire and taxi dipatching, office communications, paging in department stores, restaurants, bowling alleys, factories, schools, fast food outlets, movie theaters, etc.

Next

Astatic

astatic microphone 878hl

The high impedance position is 40,000 ohms and the low impedance is 400 ohms. The high impedance position is 40,000 ohms and the low impedance is 400 ohms. This omnidirectional Astatic desktop microphone is a dual impedance, dynamic mic that offers modern styling and features in a rugged Cycolac housing. White is almost always the mic-audio line. An output impedance compatible with the inputs of almost all commercial transceivers and externally adjustable high gain amplifier ensures desired modulation level. The first posts you make on the forum will be moderated.

Next